Hand stained and fired 3mm sheet glass.
Hand cut 3 mm stained glass and sheet mirror mounted on a fiberglass mesh:

Mesh : Details below.
Adhesive: 3M(TM) Fastbond (TM) - Details below

Dimensions: weight, size, volume - units of measurement per Meshglass sheet:
Approx 30 x 30 cm x 3mm stained glass; Sheet shape is determined according to interlocking pattern.

Weight; Approx 700 Grams or 1.6 Lbs per square foot.

Variations: Crystalmeshglass (additional 10mm Swarovski crystals in design)
35 stained glass colours, plus mirror and crystal in any mix.

Customization: YES

Visual - combine colour choices and patterns with visual design tools.
(Download Free Meshglass design tool software at www.meshglass.com)
Additional Customization: Colours can be fired to your own required décor colors. Some pattern sizes can be scaled up if required.

Technical properties: Water and fire resistant.
Contour friendly. Bonds easily to interior and exterior surfaces. +40,000 colour and pattern décor combinations.
Glass has known Thermal and heat transfer properties

Environmentally friendly.
Percent recyclable content: 100% (Glass is 100% recyclable)
Percent post consumer recycled content: EST 98%
Durable; UV resistant fade free colours.

Applications: Interior and exterior décor surfacing: Bonds to most surfaces; ceilings, walls, columns, kitchens, counters, architectural accents, murals, spas, plunge pools, bath and rest rooms, cocktail lounge,club and resort décor.

Fiberglass mesh backing material; MESH DIMENSIONS - millimeter 5 x 5mm
WEFT 20 FILI/10 cm
MEDIUM WEIGHT > 145 g /mq
CONTAINED IN RESIN 18/20 %
RESISTANCE to TENSION (N/50 millimeter) WEFT 1350
RESISTANCE TO ALKALIS: 5% AFTER 28 DAYS OF IMMERSION IN Na (OH)
MEDIUM RATE TEAR STRENGTH: 77, 8%

Adhesive; water based 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive:

Data Sheet.

3M Center St. Paul, Minnesota 55144-1000
1-800-364-3577 or (651) 737-6501 (24 hours)

DIVISION: ENGINEERED ADHESIVES
TRADE NAME: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear
ID NUMBER/U.P.C.:
62-4261-5535-4 00-21200-85834-5 62-4261-7530-3 00-21200-85868-0
62-4261-8530-2 00-21200-85780-5 62-4261-9530-1 00-21200-85781-2

ISSUED: May 30, 2001
SUPERSEDES: April 23, 2001
DOCUMENT: 11-6458-1

1. INGREDIENT C.A.S. NO. PERCENT

WATER................................... 7732-18-5 50.0 - 60.0
ACRYLIC POLYMER......................... 9017-68-9 35.0 - 45.0
SODIUM DODECYLBENZENESULFONATE.......... 25155-30-0 0.5 - 1.5
POLY(METHYL METHACRYLATE)............... 9011-14-7 < .5
AMMONIUM HYDROXIDE...................... 1336-21-6 < .5

IN CASE OF EMERGENCY: THE NUMBERS AT THE TOP OF THIS PAGE PROVIDE 24 HOUR RESPONSE FROM ANY PHONE FOR ALL EMERGENCIES WITH THIS PRODUCT.
The components of this product are in compliance with the chemical notification requirements of TSCA.
This product contains the following toxic chemical or chemicals subject to the reporting requirements of Section 313 of Title III of the Emergency Planning and Community Right-To-Know Act of 1986 and 40 CFR Part 372:
AMMONIUM HYDROXIDE

2. PHYSICAL DATA

BOILING POINT:................. > 210.00 F
VAPOR PRESSURE:................ N/A
VAPOR DENSITY:................. N/A
EVAPORATION RATE:.............. N/A
SOLUBILITY IN WATER:........... Disperses in water
SPECIFIC GRAVITY:.............. 1.040 Water=1
PERCENT VOLATILE:.............. ca. 57.00 % by wt
pH:............................ 8.00 - 8.50

-----------------------------------------------------------------------------

Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear

May 30, 2001 PAGE 2

2. PHYSICAL DATA (continued)

VISCOSITY:..................... 9000.0 - 10000.0 centipoise
MELTING POINT:................. N/D
APPEARANCE AND ODOR: liquid, clear, distinct odor

3. FIRE AND EXPLOSION HAZARD DATA
FLASH POINT:................... > 200.00 F
FLAMMABLE LIMITS - LEL:........ N/A
FLAMMABLE LIMITS - UEL:........ N/A
AUTOIGNITION TEMPERATURE:...... N/D
EXTINGUISHING MEDIA: Water spray, Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Not applicable.
NFPA HAZARD CODES: HEALTH: 1 FIRE: 0 REACTIVITY: 0
UNUSUAL REACTION HAZARD: none

4. REACTIVITY DATA

STABILITY: Stable
INCOMPATIBILITY - MATERIALS/CONDITIONS TO AVOID: Not applicable.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide and Carbon Dioxide, Aldehydes, Ketones, Toxic Vapors, Gases or Particulates.
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear

May 30, 2001 PAGE 3

5. ENVIRONMENTAL INFORMATION

SPILL RESPONSE: Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Cover with absorbent material. Collect spilled material. Place in a U.S. DOT-approved container.

RECOMMENDED DISPOSAL:
Incinerate in an industrial or commercial facility in the presence of a combustible material. Dispose of completely cured (or polymerized) material in a sanitary landfill.

ENVIRONMENTAL DATA:Not determined.

REGULATORY INFORMATION:
Volatile Organic Compounds: 1 gms/liter South Coast Air Quality Mgmt Dist Method Rule 443.1, calculated.

VOC Less H2O & Exempt Solvents: 2 gms/liter South Coast Air Quality Mgmt
Dist Method Rule 443.1, calculated.

Since regulations vary, consult applicable regulations or authorities before disposal. U.S. EPA Hazardous Waste Number = None (Not U.S. EPA Hazardous). EPCRA HAZARD CLASS:
FIRE HAZARD: No PRESSURE: No REACTIVITY: No ACUTE: Yes CHRONIC: No

6. SUGGESTED FIRST AID

EYE CONTACT: Immediately flush eyes with large amounts of water. Get immediate medical attention.
SKIN CONTACT: Flush skin with large amounts of water. If irritation persists, get medical attention.
INHALATION: If signs/symptoms occur, remove person to fresh air. If signs/symptoms continue, call a physician.
IF SWALLOWED: Do not induce vomiting. Drink two glasses of water. Call a physician.

---------------------------------------------------------------------

Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear
May 30, 2001 PAGE 4

7. PRECAUTIONARY INFORMATION

EYE PROTECTION: Avoid eye contact. Wear vented goggles. Wear safety glasses with side shields.
SKIN PROTECTION: Avoid prolonged or repeated skin contact. Wear appropriate gloves when handling this material. A pair of gloves made from the ollowing material(s) are recommended: butyl rubber, neoprene, nitrile rubber.
RECOMMENDED VENTILATION: Do not use in a confined area or areas with little or no air movement. Use in a well-ventilated area. Provide sufficient ventilation to maintain emissions below recommended exposure limits. If exhaust ventilation is not adequate, use appropriate respiratoryprotection.
RESPIRATORY PROTECTION: Avoid prolonged breathing of vapors. Select one of the following
NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: half-mask organic vapor respirator.
PREVENTION OF ACCIDENTAL INGESTION: Do not ingest.

RECOMMENDED STORAGE: Store at temperatures above 32 degrees F (O degrees C). Keep container closed when not in use. Keep out of the reach of children.

FIRE AND EXPLOSION AVOIDANCE: Keep container tightly closed.
EXPOSURE LIMITS
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
WATER................................ NONE NONE NONE NONE
ACRYLIC POLYMER...................... NONE NONE NONE NONE
SODIUM DODECYLBENZENESULFONATE....... NONE NONE NONE NONE
POLY(METHYL METHACRYLATE)............ NONE NONE NONE NONE
AMMONIUM HYDROXIDE................... 35 PPM STEL CMRG
AS AMMONIA
AMMONIUM HYDROXIDE................... 25 PPM TWA CMRG
AS AMMONIA

* SKIN NOTATION: Listed substances indicated with 'Y' under SKIN refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye, either by airborne or, more particularly,
Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear
May 30, 2001 PAGE 5

EXPOSURE LIMITS (continued)
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
by direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
- CMRG: Chemical Manufacturer Recommended Exposure Guidelines
- NONE: None Established

8. HEALTH HAZARD DATA

EYE CONTACT: Mild Eye Irritation: signs/symptoms can include redness, swelling, pain, and tearing.
SKIN CONTACT: Mild Skin Irritation (after prolonged or repeated contact): signs/symptoms can include redness, swelling, and itching.
INHALATION: Irritation (upper respiratory): signs/symptoms can include soreness of the nose and throat, coughing and sneezing.
IF SWALLOWED: Ingestion may cause: Irritation of Gastrointestinal Tissues: signs/symptoms can include pain, vomiting, abdominal tenderness, nausea, blood in vomitus, and blood in feces.

---------------------------------------------------------------------

SECTION CHANGE DATES

---------------------------------------------------------------------

HEADING SECTION CHANGED SINCE April 23, 2001 ISSUE

---------------------------------------------------------------------

Abbreviations: N/D - Not Determined N/A - Not Applicable CA - Approximately
MSDS: 3M(TM) Fastbond(TM) Pressure Sensitive Adhesive 4224 NF Clear
May 30, 2001 PAGE 6

---------------------------------------------------------------------

The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.

3M provides information in electronic form as a service to its customers.

Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.

Copyright, 2001, Minnesota Mining and Manufacturing Company.All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that:

1) The information is copied in full with no changes unless prior agreement is obtained from 3M, and
2) Neither the copy nor the original is resold or otherwise distributed